521 reviews analysed
1. Viton Rubber Gasket Tri-clamp O-Ring Fits to Sanitary Tri-Clover Type Ferrule- 2 Inch (Pack of 5)
Feature
- 5 pcs Viton Tri Clamp Gasket- fits to standard 2″ tri-clover or tri-clamp fittings, apply to Pipe Outer Dia: 51mm / 2″.
- Outer Diameter : 64mm / 2.5″.
- Inner Hole Diameter : 48mm / 1.89″. Thickness (Max.) : 4.8mm / 0.19″.
- Chemical Resistance-Made from food grade Viton Rubber, EPDM Synthetic Rubber.
- Temperature Rating (spec): -30℉ to 400℉.
2. 117 Viton O-Ring, 75A Durometer, Black, 13/16" ID, 1" OD, 3/32" Width (Pack of 25)
Feature
- Made of Viton (fluorocarbon elastomer) for use with a variety of chemicals and fuels
- Round cross-section to provide a seal between cylindrical overlapping surfaces
- Can be used across a wide temperature range from -15 degrees F (-26 degrees C) to 400 degrees F (205 degrees C)
- Durometer (hardness) of 75A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This Viton O-ring is black in color, round in shape, has a durometer (hardness) of 75A, and is designed for use in a wide variety of sealing applications.
Viton has excellent heat, fuel, and chemical resistance. Viton is acceptable for temperature applications between -15 degrees F (-26 degrees C) to 400 degrees F (205 degrees C). It is compatible for use with non-flammable hydraulic fuels, silicone oil, chlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons (benzene) and aliphatic hydrocarbons (propane), as well as high vacuum environments, ozone, and weathering. Viton is vulnerable to low molecular organic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and super-heated steam.
This Viton O-ring has a shore durometer of 75A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This Viton O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
3. 207 Buna-N O-Ring, 70A Durometer, Black, 9/16" ID, 13/16" OD, 1/8" Width (Pack of 100)
Feature
- Made of Buna-nitrile (also called Buna-N) for use with a variety of fluids and hydrocarbons
- Can be used across a wide temperature range from -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This O-ring is made of black Buna-nitrile, is round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications.
Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance. It can be used in temperatures between -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C), and is compatible for use with petroleum, HFA, HFB and HFC fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering and should therefore not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light.
This Buna O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
These Buna-nitrile O-rings meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
4. 115 Silicone O-Ring, 70A Durometer, Red, 11/16" ID, 7/8" OD, 3/32" Width (Pack of 100)
Feature
- Made of silicone for use with a variety of chemicals and fluids
- Can be used across a wide temperature range from -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications.
Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
5. 316 Silicone O-Ring, 70A Durometer, Red, 7/8" ID, 1-1/4" OD, 3/16" Width (Pack of 25)
Feature
- Made of silicone for use with a variety of chemicals and fluids
- Can be used across a wide temperature range from -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications.
Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
6. 211 Buna-N O-Ring, 70A Durometer, Black, 13/16" ID, 1-1/16" OD, 1/8" Width (Pack of 100)
Feature
- Made of Buna-nitrile (also called Buna-N) for use with a variety of fluids and hydrocarbons
- Can be used across a wide temperature range from -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This O-ring is made of black Buna-nitrile, is round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications.
Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance. It can be used in temperatures between -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C), and is compatible for use with petroleum, HFA, HFB and HFC fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering and should therefore not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light.
This Buna O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
These Buna-nitrile O-rings meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
7. 207 Silicone O-Ring, 70A Durometer, Red, 9/16" ID, 13/16" OD, 1/8" Width (Pack of 100)
Feature
- Made of silicone for use with a variety of chemicals and fluids
- Can be used across a wide temperature range from -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications.
Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
8. 318 Silicone O-Ring, 70A Durometer, Red, 1" ID, 1-3/8" OD, 3/16" Width (Pack of 25)
Feature
- Made of silicone for use with a variety of chemicals and fluids
- Can be used across a wide temperature range from -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications.
Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
9. 019 Silicone O-Ring, 70A Durometer, Red, 13/16" ID, 15/16" OD, 1/16" Width (Pack of 100)
Feature
- Made of silicone for use with a variety of chemicals and fluids
- Can be used across a wide temperature range from -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications.
Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
10. 116 Silicone O-Ring, 70A Durometer, Red, 3/4" ID, 15/16" OD, 3/32" Width (Pack of 100)
Feature
- Made of silicone for use with a variety of chemicals and fluids
- Can be used across a wide temperature range from -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C)
- Round in cross-section to provide a seal between cylindrical overlapping surfaces
- Durometer (hardness) of 70A for resistance to penetration
- Meets standards defined by Aerospace Standard AS568A
Description
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications.
Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels.
O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation.
This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
Conclusion
By our suggestions above, we hope that you can found Viton Oring Water Heating Element for you.Please don’t forget to share your experience by comment in this post. Thank you!
