Top 10 3D Printer Heating Controller

* With independent temperature controller .need plug with independent power * Size: 510-510mm suit for CR-10S5.
*Power consumption :Maximum power 1200W
*The maximum heating temperature 120C（Celsius Degree）
* The back with 3M adhesive glue, can directly stick to the heated bed. need disassemble the S5 bed before assemble it
* The heated bad Maximum temperature resistant is 200C, long term working temperature condition is under 180C
* This is 28 hole version, beyond 24 postion hole, extra 4 hole is for cooling
* To ensure safety , the plugs are 3 pins
* When use, please do some test to find a suitable temperature for you to use, for example, when heating pad working , if you want heat the bed to 100C, please set the silicon heater to 75-80C, no need to set to 100C, for the printer itself can heat too. this can save electricity cost and environment friendly

Fahrenheit and Celsius Display Can Be Choose
Temperature Calibrating, Refrigerating control output delay protection
Control the Temperature by Setting the Temperature Set Value and the Difference Value
Alarm When Temperature Exceeds the Limit or When Sensor Error
2 Relays, Switch Between Cooling and Heating Modes

Technical Parameter:
Output: 2 Relays
Temperature Measuring Range: -50～210 oF / -50 oC-99 oC
Resolution: 0.1 oF / 0.1 oC
Accuracy: ±1 oF（-50 oF -160 oF）/ ±1 oC（-50 oC -70 oC） Power Supply: 110VAC 50Hz/60Hz
Power Consumption: 3W
Sensor: NTC Sensor
Relay Contact Capacity: Cooling (10A/250VAC)/ Heating (10A/250VAC);
Ambient Temperature: 0 oC-60 oC
Storage Temperature: -30 oC-75 oC
Relative Humidity: 20-85% (No Condensate)

Package Content:
1x Temperature controller ITC 1000 110V
1x 7.87″ SENSOR
1x Muanal

Note: The Ender 3 Extruder Head Kit Suitable for Creality Ender 3.
These are original replacement parts for Creality 3D printer Ender 3.
Tip of the nozzle, aluminum heating block, throat pipe (built-in Teflon)
Ender 3 Extruder Hot End Kit, white wire was temperature thermistor, Black wire was heating tube 24V 40W

– Installation type: External thread connection
– Application: Creality 3D printers ender 3
– Nozzle size: 0.4mm
– Cable length: 1.2m
– Heating Tube: 24V 40W
– Operating temperature range: -40~+260°C (-40~+500°F)
– Material: Aluminum+Stainless Steel+Brass – Throat length: 52mm
– Aluminum block size: approx. 20 x 20 x 10mm
Package list:
1 x Aluminum Block
1 x Heating Tube
1 x M6*30mm Throat Pipe (Built-in Teflon)
1 x Thermistor +Brass Sleeve
1x 1.75mm 0.4mm Brass Nozzle
5×1.75mm 0.4mm Brass Nozzle ( as free gift)

* 310-310mm suit for CR-10 or CR-10S,410-410 suit for CR-10S4, 510-510mm suit for CR-10S5.
* 310-310 Maximum power :750W, 410-410 Maximum power 1000W, 510-510 Maximum power 1200W
*The maximum heating temperature 120C（Celsius Degree）
* The black size is 3M adhesive glue, can directly stick to the heated bed.
* The heated bad Maximum temperature resistant is 200C, long term working temperature condition is under 180C
* The position hole onlly have 4 positon holes, if you order 510-510mm, Please check if your heated bed is latest verison which have 24 positon holes, please contact us for delivery time
* To ensure safety , the plugs are 3 pins, please choose Plug type according to your aera, US plug’s voltage 110V-120V, UK/EU plug ‘s voltage is 220-240V, if your plug is different, please leave message to us to ask us if we can supply according to your requriement
* When use, please do some test to find a suitable temperature for you to use, for example, when use 410-410 version , if you want heat the bed to 100C, please set the silicon heater to 75-80C, no need to set to 100C, for the printer itself can heat too. this can save electricity cost and environment friendly

Important Notes: 1)——-Please read the Controller Configuration Manual, especially the “Advanced Setting” part, carefully BEFORE making any changes on the controller. 2)——-The controller unit is 100% brand new. But due to manufacturing reasons, stains, dusts or scratches may be present on the silicone case. The case may also fit loosely. Please consider this before the purchase. 3)——–Please heat only when after it’s mounted onto the build plate (Aluminum plate recommended). A supporting frame/layer is strongly suggested to have the heating element “sandwiched” tightly for better heating result.

Description:
– Universal heated bed power expansion module high power module for 3D printers
– Effectively solve the problem that the heat bed power is too large and the load current issue
– Helps 3D printers with controller boards (capable of max 15A) become more powerful
– With this additional module, the maximum current on the board can reach 25A
– Note: If you plan to use a heated bed with your 3D printer that uses a 12V power supply, then this module is recommended; otherwise, it may cause excessive current and may burn out the connectors on the controller board

Specification:
– Size (L x W x H): Approx. 6 x 5 x 3.5 cm/2.4 x 2 x 1.4 inches
– Wire Length: Approx. 20 cm/7.9 inches
– Max Current: 25A (Enhance heat dissipation)

Instruction:
1.Remove basically all outside screws for your Anet A8 control box
2.Take pictures of existing board wiring
3.Unscrew two large 12 / 14GA wires on the board labeled HOT BED
4.Screw these two wires into the new MOSFET board labeled HOT BED
5.Connect the small jumper wires (white) to the control board where 6.you just remove the two wires and screw them down. Note the 7.polarity on each board. Match ( + ) to ( + ) and ( – ) to ( – )
8.Find 2 x 6 – 8 inches pieces of 12 or 14 AWG wire
9.Run one of the 6 inches wires to the power supply ( + ), screw in. 10.The other side to the (+) DC on the new MOSFET board. Repeat for the negative wire (-) to (-)
11.many people use Velcro to secure the new board to the top of the control box.
12.Put everything back together
13.when complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package includes:
5 x MOS Heat Dissipation Module
5 x Cable